Sold in pairs.
- Wheels Setup: 4x65mm with UFS mounting or 4x68mm with soulframe mounting
- Mount: UFS
- Sizes: XL=276mm
- Material: AL 6061 aircraft
- Included Accessories: AL spacer, mounting screws, does not incl. mounting antirivets
Choosing the correct skate size is a very important task and usually even more important than choosing the skates model! All high-quality skates will have a break in period and would adjust over time to the skater’s feet. Some will take longer and some shorter, but while you want to have a comfortable ride you do not want to have the skates too loose… The correct fit will determine much more than just the comfort - it will define how much control, power transfer, and agility you would have while skating, and even would affect the balance.
While various skating styles and skaters themselves have different preferences, below are the general instructions of how to determine the perfect fit for your new skates.
Most of inline and roller skates are manufactured and sold in European sizes (EU), so your US / UK sizing could be a wrong idea to use due to the conversion inaccuracies. Furthermore, even if you know your European sizing, every shoe and skate manufacturer has a slightly different fit and sizing, therefore your standard shoe size might not assure a perfect fit but that is the best way to estimate your skate size. In any case, the inline and roller skate size should be either equal to your shoe size or no more than one size up or down from it.
Based on our experience, the best way to determine your skate size is to take a look at your current pair of skates and/or running shoe labels for MM / CM / MP / MONDO numbers. These numbers are indicating the maximum foot length that will fit into the pair, while MM shows the measurement in millimeters and CM/MP/MONDO is centimeters. Having these numbers along with the EU sizes from these shoes, you will be able to determine the size of the skates that you need by looking into brand or model specific sizing chart (usually located in the Sizing tab under the skates photos or as one of the product photos). If cannot be located, please send us an inquiry and we gladly will help you out!
Important: Many shops are recommending measuring your feet to determine your skate size, but we have found that this leads to too many mistakes and do not recommend that. If after following the instructions above you are finding yourself stuck in between two sizes, you could measure your feet according to the directions below. In this case, your shoe size is still the defining factor, so if the measurement is showing more than one size up or down, something is wrong with the measurement! If your foot is wider than average, please go one size up. Usually, Seba, FR, and Adapt skates fit wider than average, Powerslide and K2 average, Flying Eagle and Rollerblade average to narrow...
You’ll need paper, pen, a flat wall and, if possible, a buddy to help. It’s best to measure your feet later in the day after you have been on them for a few hours to account for swelling.
Find a hard floor with a flat wall. Tape a piece of paper down so that it touches the wall. Stand on the paper in bare feet, with your heel just touching the wall.
Have your friend take a book and place it so that it just touches the tip of your longest toe. Mark the spot where the book meets your toe. Do this with both feet and use the larger of the two measurements. Measure your foot length in millimeters, if possible. If you measure in inches, be sure to measure in 16ths of an inch.
Choose your size from the manufacturers sizing chart. The “Max Foot Length” is the longest foot measurement that will fit into that size. The US Men’s column lists the sizes found on the box.
Our sizing advice is targeted to a freestyle or dance skater who wants a very snug fit in their skate to enjoy maximum control. Our instructions will give a fit that prioritizes control over comfort. If comfort is a higher priority, or if you have an especially wide or oddly shaped foot, you may do well to choose a slightly larger size. If you are near the boundary between two sizes, you would probably be better off to go with the larger size in case you prefer comfort over control.
Notes about Width
In general, the Plastic Boot skates with a built-in liner have a narrower fit through the foot, while the boots with a removable liner and soft boots have a somewhat wider fit. The Carbon is a bit wider through the toe box than the plastic boot skates because the carbon fiber boot has less flex. As a rule of thumb, skates with built-in liners and "regular" liners will have less adjustment room.
We gladly will guide you in case you have any further questions. Email us at [email protected]
To help you better, please include all the sizing information off one or two pairs of skates or running shoes that you currently have including EU/US/UK/MP/CM/MM/MONDO, etc...
After the success of the USD Aeon skate, we took a close look at its design in the development of the new Kizer Soulframe 68. We wanted to lower the center of gravity whilst increasing the direct feeling of grinding. It is completely made out of aluminum for maximum energy transfer, faster grinds, and designed specifically for the high-speed park- or bowl skating and coping grinds. Like the Aeon it is a non-UFS unibody soul plate with an integrated frame, to achieve the lowest center of gravity and widest split for flat setups, making it lighter and stronger whilst using fewer parts.
Plate and frame are made out of 6061 aircraft aluminum, CNC machined to perfection, and coming with the new Element II aluminum H-block. The Soulframe has predrilled and recessed mounting holes which are compatible fit most USD skates and also Salomons. The 68 version is designed specifically for 68mm and 64mm flat setups, making the Soulframe 68 one of the fastest and most stable flat setups available in modern aggressive skating.
6 in stock
Sold in pairs.
|Frame Length (mm)|